I have been playing with Tinkercad ... would this print OK ?

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Thread Modes

I have been playing with Tinkercad ... would this print OK ?

Kevan
Build-Race-Enjoy-Improve-Repeat

Posts: 4,528
Threads: 147
Likes Received: 3,066 in 1,819 posts
Likes Given: 4,215
Joined: Apr 2019
Location Isle of Man

#14

8th-May-23, 08:41 PM

I use one of these...carefully, with the bevel upwards.

...I did stone the sharp edge off though Thumbup

Life is like a box of Slot cars... Cool

1 member Likes Kevan's post

Find

Quote

« Next Oldest | Next Newest »

Messages In This Thread

I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 03:27 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 6th-May-23, 04:37 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 05:47 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 6th-May-23, 05:58 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 6th-May-23, 09:09 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 6th-May-23, 09:55 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 7th-May-23, 02:55 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 7th-May-23, 04:14 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 7th-May-23, 04:59 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 7th-May-23, 07:34 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 05:57 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 8th-May-23, 06:46 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 08:01 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 8th-May-23, 08:41 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 8th-May-23, 08:52 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by chappyman66 - 9th-May-23, 04:16 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 9th-May-23, 08:07 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 10:12 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by OXO cube - 9th-May-23, 10:35 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 11:11 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 12:33 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by JMay - 9th-May-23, 12:20 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 12:25 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 9th-May-23, 01:35 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 9th-May-23, 01:53 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 9th-May-23, 10:35 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 10th-May-23, 06:04 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 10th-May-23, 06:56 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by chappyman66 - 10th-May-23, 02:22 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 12th-May-23, 05:13 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 12th-May-23, 05:54 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 13th-May-23, 12:40 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 08:21 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Savage GT - 13th-May-23, 11:48 AM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 02:39 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by Kevan - 13th-May-23, 09:48 PM

RE: I have been playing with Tinkercad ... would this print OK ? - by MrFlippant - 14th-May-23, 05:42 PM

Possibly Related Threads...

Thread / Author Replies Views Last Post

resin print request

OXO cube

765

Last Post by Kevan
4th-Jan-26, 08:33 PM

FDM Print Bed Sheets

Kevan

1,424

Last Post by MrFlippant
13th-Aug-22, 10:05 PM

The best all round FDM print surface you've probably not heard of...

Kevan

999

Last Post by Kevan
13th-Nov-21, 01:30 AM

What surface to 3D print on...GRP???

Kevan

2,308

Last Post by Kevan
24th-Oct-21, 11:40 AM

My first 3dp print

AlexisGaitanis

24,088

Last Post by AlexisGaitanis
14th-Mar-20, 09:01 PM

View a Printable Version

Forum Jump:

Users browsing this thread: 1 Guest(s)